Skip to Content

Cabling standards today: Cat6A for new installs and fiber in the building

What to run in the walls for new construction and renovations, and where fiber belongs
November 20, 2026 by
Cabling standards today: Cat6A for new installs and fiber in the building
Dee plugging in a cable

Short version: for new construction and major renovations, run Category 6A copper to every outlet and access point, and use fiber between equipment rooms, floors and buildings. The cable is in the walls for 15 years or more, so build for the equipment you will have later, not just what you plug in today.

Cabling is the one part of a technology system you only want to install once. Switches, access points and cameras get replaced every few years; the cable behind them usually stays for the life of the building. Here is what current industry practice calls for, in plain English.

Copper: Category 6A is the default for new work

The TIA commercial building cabling standards recommend Category 6A for new installations, and manufacturers and designers have followed. Cat5e is no longer a sensible choice for new work, and plain Cat6 is now mostly for small additions to an existing Cat6 system.

Cable10-gigabit reachWhere it fits today
Cat5eNot ratedExisting systems only. Do not install new.
Cat6About 55 meters, conditions permittingSmall adds to an existing Cat6 system, short desk or phone runs
Cat6AFull 100 metersNew construction, renovations, Wi-Fi access points, cameras and PoE devices
Cat830 metersData center equipment rows only. Not for building wiring.

Why Cat6A

  • Speed at full length. Cat6A carries 10 Gb/s across the full 100-meter channel. Cat6 only gets there on shorter runs.
  • Power over Ethernet is growing. Access points, cameras, door controllers, displays and even lighting now run on PoE, up to 90 watts per port with the newest standard. Power makes cable bundles warm, and Cat6A's larger construction handles that heat better.
  • Wi-Fi keeps getting faster. Wi-Fi 6E and Wi-Fi 7 access points ship with 2.5, 5 and 10 Gb/s ports. TIA's wireless cabling guidance recommends two Cat6A runs to each access point location, for speed and for a backup path.
  • The cost difference is small. Most of a cabling job is labor. Upgrading the cable itself adds a modest amount to the total, and it is far cheaper than pulling new cable through finished ceilings later.

Shielded or unshielded?

Unshielded Cat6A (U/UTP) is right for most offices, condos and retail. Shielded Cat6A (F/UTP) makes sense near heavy electrical noise, such as elevator rooms, mechanical spaces and some medical or industrial areas. Shielded systems only work when they are bonded and grounded correctly from end to end, so the whole system has to be designed that way, not mixed.

Fiber inside the building

Copper is limited to about 100 meters, so anything longer, or anything between floors and buildings, belongs on fiber. Fiber also carries no electricity. Between buildings that matters a lot on the Gulf Coast: a copper link between buildings can carry a lightning surge into your equipment, and fiber cannot.

FiberWhat it isWhere it fits
OS2 single-modeSmall core, yellow jacket, very long distancesBuilding-to-building, risers and backbones you want to last. The cost of single-mode optics has dropped, so many designers now use it as the default backbone.
OM4 multimodeLarger core, aqua or violet jacket, shorter distancesShort runs inside one building or one equipment room, where lower-cost optics help
OM1 / OM2Older orange-jacket multimodeExisting systems only. Plan to replace when you upgrade.

Fiber good practices

  • Pull spare strands. The cost is in the labor, not the glass. A 12-strand cable where you need two gives room for growth and repairs.
  • When in doubt, run both or a hybrid. A cable with single-mode and multimode strands covers today's equipment and tomorrow's.
  • Use the right jacket. Plenum (OFNP) or riser (OFNR) ratings inside, and outdoor or indoor/outdoor cable in conduit between buildings.
  • Protect it. Fiber in innerduct or armored cable survives other trades working in the same ceiling.
  • Test and document. Every strand gets a loss test, with results in your closeout package.

Pathways, labeling and testing

Good cable in a bad pathway still fails. On a standards-based job you should see:

  • Conduit and sleeves sized with room to add cable later
  • J-hooks or cable tray supporting cable every 4 to 5 feet, never cable lying on ceiling tiles
  • Low-voltage kept apart from electrical power runs
  • Every jack, patch panel port and fiber strand labeled to match the drawings
  • Certification test reports for every copper link and loss reports for every fiber
  • As-built drawings when the job is done

Quick guide for owners and GCs

ProjectWhat to specify
New office, retail or condo build-outCat6A to every outlet, two Cat6A per Wi-Fi access point, fiber backbone to each telecom room
Multi-building campus or resortOS2 single-mode between buildings in conduit, Cat6A inside each building
Adding a few drops to an older systemMatch the existing category if it tests well; plan Cat6A for the next major renovation
Cameras and access controlCat6A for PoE devices, with cable runs kept under 100 meters or fed from a closer closet

Standards referenced: the TIA-568 commercial building cabling series and TIA's guidelines for cabling wireless access points (TSB-162). Specific project requirements can vary; your design should follow the current editions and any owner or spec requirements.

Dee giving a thumbs up

Planning new construction or a renovation?

DES designs with an RCDD and builds to BICSI standards: Cat6A, fiber backbones, labeled, tested and documented. Serving Destin, the Emerald Coast, Mobile, Huntsville and Atlanta.

Start a cabling project or call 850-502-8567
Camera system checklist: 8 things to confirm before you sign a quote
For condo associations, restaurants, hotels and offices comparing security camera bids.